Daniel:Notebook/PosSequencing/2017-6-22: Difference between revisions

From ZhangLabWiki
Jump to navigation Jump to search
>Djacobse
(Created page with "=Beadless emPCR= Back to calendar This is to test the emPCR without using beads. ==Protocol== <ol> <li>Oil phase</li> <ol type="A"> <li>...")
 
>Djacobse
Line 12: Line 12:
<li>Mix 5 uL Triton X, 40 uL Tween-80, and 450 uL Span 80 into 2 mL Mineral oil and 8 mL Tegosoft DEC</li>
<li>Mix 5 uL Triton X, 40 uL Tween-80, and 450 uL Span 80 into 2 mL Mineral oil and 8 mL Tegosoft DEC</li>
<li>Vortex vigorously to mix</li>
<li>Vortex vigorously to mix</li>
 
</ol>
<li>Aqueous Phase Preparation</li>
<li>Aqueous Phase Preparation</li>
<ol type="A">
<ol type="A">

Revision as of 20:38, 22 June 2017

Beadless emPCR

Back to calendar

This is to test the emPCR without using beads.

Protocol

  1. Oil phase
    1. Mix 5 uL Triton X, 40 uL Tween-80, and 450 uL Span 80 into 2 mL Mineral oil and 8 mL Tegosoft DEC
    2. Vortex vigorously to mix
  2. Aqueous Phase Preparation
    1. Wash beads with 100 uL wash buffer; vortex to suspend; apply magnet and remove supernatant
    2. Repeat wash step
    3. Resuspend beads in 10 uL TE buffer
    4. Mix ingredients using the following table
    5. Component uL Added uL Added Final Concentration
      DreamTaq 10X PCR Buffer (20 mM MgCl2) 10 10 1X
      10 mM dNTPs 10 10 1 mM
      25 mM MgCl2 6 6 3.5 mM
      10 uM Primer A (Free primer-Primer 2) 10 10 1 uM
      10 uM dual biotin primer 0.5 0.5 0.1 uM
      Hydrogel beads, 2M/uL 10 10 25 M
      DreamTaq Polymerase (5 U/uL) * 2 2 10 Units
      Barcode Oligo v1 (template, 100 pM, 100 nM) 5 5* 10 pM, 10 nM*
      100 mM Ammonium Sulfate 5 5 5 mM
      1 mM Spermidine*** 10 10 100 uM
      TIPP 0 0 0
      Water 36.5 36.5 NA
      Total Volume 100 100  
  3. Oil-Aqueous Mixing
    1. Mix 10 uL aqueous into 100 uL oil mixture
    2. Vortex for 30 seconds
    3. Repeat mixing to 100 uL (5 times)
    4. Mix with vortexer for 3 minutes
    5. Dilute with pure mineral oil for imaging (1:100)
    6. Distribute 150 uL total volume into 3 tubes, 50 uL each; use same pipette tip
  4. Emulsion PCR
    1. Perform PCR with the following settings
      1. 95C 2 min
      2. 95C 20 sec
      3. 58C 30 sec
      4. 70C 30 sec
      5. Goto b 50 times
      6. 4C forever